Every time your thermostat calls for heat, the furnace works through a fixed checklist. The inducer motor starts and proves draft by closing a pressure switch, the hot surface igniter heats up, the gas valve opens, the burners light, and the flame sensor confirms there is fire. Only after all of that does the blower begin sending warm air into the house. Finding the step that fails is most of the job. Around Sunrise, FL, the usual failure points are an oxide-coated flame sensor, an igniter cracked by years of heating and cooling, a pressure switch that stays open because of a weak inducer or a clogged condensate trap on a high-efficiency unit, and control boards with burned relays. Each one halts the startup, and from the hallway they all look alike.
Rather than guess, Sunrise HVAC tests the sequence stage by stage. We read igniter resistance, measure flame signal in microamps, check that the pressure switch responds to real inducer draft, confirm voltage at the gas valve, and test the blower and its capacitor. Because this is a fuel-burning appliance, the safety basics come with every visit: we inspect the heat exchanger, leak-test the gas connections, and verify flue draft. You cannot tell a furnace problem from a furnace hazard by looking at the thermostat. Before we leave, temperature rise is measured against the data plate so airflow and flame are matched as the manufacturer intended.
Sunrise HVAC services natural gas, propane, and electric furnaces of every major brand, from standard 80 percent units to condensing high-efficiency models with their traps, drain lines, and dual pressure switches. Our trucks carry the parts that really fail, such as igniters, flame sensors, pressure switches, capacitors, inducer assemblies, and blower motors, so most homes have heat again before we leave. Call (754) 334-0984 for furnace repair anywhere in Sunrise, and an experienced technician will be on the way today.
When the AC quits in summer, see AC Repair in Sunrise.
How Much Does Furnace Repair Cost in Sunrise?
For most Sunrise homes, a furnace repair runs $150 to $600. Ignition and sensor problems are usually the least expensive, while blower motors, control boards, and heat exchangers cost more. You'll get a written, upfront price from Sunrise HVAC after we diagnose the problem.
| Repair | Typical cost | What it usually means |
|---|---|---|
| Flame sensor cleaning or replacementBurners light but cut out almost immediately | $80–$250 | Burners light but cut out almost immediately |
| Hot surface igniter replacementFurnace clicks and tries to start but never lights | $150–$400 | Furnace clicks and tries to start but never lights |
| Draft inducer motorLoud humming or grinding at startup, then lockout | $400–$1,000 | Startup fan fails, furnace won't fire |
| Blower motorBurners run but little or no air comes out of the vents | $400–$1,500 | Burners run but little or no air comes out of the vents |
| Control boardErratic behavior, error codes, or no response at all | $300–$700 | Furnace won't respond to the thermostat |
| Gas valve replacementIgniter glows but gas never flows to the burners | $250–$700 | Igniter glows but gas never flows to the burners |
Ranges are typical for these repairs; you get an exact quote before any work starts.
Factors That Change the Price
- Furnace age and type, because 90%+ efficiency models have more specialized parts
- Whether a cracked heat exchanger is found, which usually means replacement rather than repair
- Timing, such as a no-heat call on a cold night versus a scheduled repair
- How easy the furnace is to reach
When a repair gets expensive on an aging furnace, you'll see both options before deciding. Call (754) 334-0984 for a quote.
Warning Signs for Furnace Repair
Spotting the early warning signs gives you the chance to act before the situation spirals into something far more expensive. Watch for these telltale signs that professional help is needed:
- A pilot or burner flame that is lazy yellow instead of crisp blue
- Clicking and a glowing igniter with no burner flame
- Squealing or grinding from the blower compartment
- Air moving through the vents that never gets warm
- A bang or boom when the burners ignite late
- Repeated shutdowns just seconds after the burners light
- Water, rust stains, or black soot around the flue or cabinet
- A furnace that shuts off every few minutes before the house warms up
Don't Wait for a Total Failure
Most HVAC failures start small, a weak capacitor, a squealing blower, a system that runs a little longer each week. Call Sunrise HVAC at (754) 334-0984 at the first sign of trouble.
Furnace Repair Issues? We Can Help.
Call Sunrise HVAC for fast, reliable service.
Call (754) 334-0984 TodayFrequently Asked Questions About Furnace Repair
Why Professional Furnace Repair Matters
A furnace combines gas, flame, high voltage, and a flue in one cabinet, and the failure that matters most is the one you cannot see from outside: a compromised heat exchanger passing combustion gases into the air your blower pushes through the house. Delayed ignition that booms at light-off stresses that exchanger further every morning it goes unfixed. Meanwhile the diagnostic traps stack up: a furnace that trips its high limit may have a bad switch, or it may be protecting itself from a clogged filter or a dying blower, and replacing the switch in the second case just removes a safety while leaving the fault.
Our experienced technicians treat every symptom as a question about the whole system. Flame signal gets measured rather than assumed, so a healthy sensor is never replaced while a cracked igniter or weak gas valve skates by. Draft is verified at the pressure switch and the flue. Temperature rise is checked against the data plate, which is how airflow problems get caught before they shorten the exchanger's life. And the gas side is leak-tested with instruments, not a sniff and a shrug. The result is a furnace that has been proven safe and correct under a full cycle, and an honest report if the unit is nearing the point where replacement beats another repair.
Our Furnace Repair Process
Every visit follows a step-by-step method refined over years of hands-on experience. Here's exactly how the furnace repair process unfolds:
Startup Sequence Testing
The furnace is run through its startup while we measure inducer draft, pressure switch response, igniter resistance, flame signal, and gas valve operation. The goal is to pinpoint the exact step that fails.
Combustion Safety Check
Every repair includes a safety check: heat exchanger inspection, instrument leak testing on the gas side, and flue draft verification, because a furnace that runs is not the same as a furnace that runs safely.
Expert Repair
Igniters, flame sensors, pressure switches, capacitors, and motors ride on the truck, so most furnaces are lit and heating again before we pack up.
Full Verification
Before we head out, the furnace runs full cycles while we check temperature rise against the data plate, listen for clean, quiet ignition, and test each limit and safety control.
Maintenance Tips for Furnace Repair
A few simple habits now, like regular filter changes and seasonal tune-ups, can add years to your system's life. Put these technician-approved steps to work around your property:
- Keep a working carbon monoxide alarm on every level of the home and check it each month
- Book a fall tune-up so weak igniters and fouled sensors are caught before the first freeze
- Avoid packing the utility room, because burners need open space for combustion air
- Put in a fresh filter monthly through the heating season, the cheapest protection your furnace can get
- If you have a high-efficiency furnace, check that the condensate drain is flowing freely
- Keep storage, lint, and especially chlorine-based products away from the furnace closet
- Notice how the furnace sounds at startup, because a quiet light-off is healthy and a boom is not
Comparing DIY and Professional Furnace Repair
A homeowner can swap a filter with ease, but diagnosing capacitors, refrigerant charge, control boards, and error codes calls for the equipment and know-how only a pro brings. Here's a comparison:
| Factor | DIY Attempt | Professional Service |
|---|---|---|
| Exchanger Cracks | Damage hidden inside the cabinet | Examined as standard on each call |
| Ignition Problems | Guesswork based on blink codes | Each ignition component tested |
| Gas Safety | Connections judged by smell | Instrument leak test on each visit |
| High-Limit Trips | Limit replaced, cause left behind | The airflow fault behind the trip found |
| Airflow Match | Blower speed left wherever it was | Blower tuned to the rated rise |
| Final Check | Declared fixed after one flame | Clean, safe operation verified over full cycles |
Get Furnace Repair Help Today
Every day you wait puts more strain on a struggling unit. Get Sunrise HVAC on the job today.
Call (754) 334-0984 TodayAreas We Serve for Furnace Repair
We serve Sunrise and its neighboring communities for furnace repair, from quick same-day repairs to planned installs.